Hot water systems are an integral part of recreational vehicles (RVs). For instance, if you own a caravan you would want it have a hot water system. There are different types of hot water systems; one of them is the Suburban hot water system. It is quite reputable but we shall be looking at some of the common Suburban hot water system problems.
Table of Contents
What Is A Suburban Hot Water System?
The Suburban hot water system is one of the most common out there. You will typically find it in Suburban RVs. The Suburban hot water system is acclaimed for its efficiency and quality. The other notable thing about the Suburban hot water system is its fast recovery. This means you virtually always have hot water no matter how frequent you may use it. That is all fair and fine but you need to know common Suburban hot water system problems.
Suburban Hot Water System Problems
The Suburban hot water system no doubt may run into some problems. This is usually inevitable and it is something to anticipate. That is why we have to discuss such problems. Here are some of the common Suburban hot water system problems:
1. System Not Working
This is obviously one of the common Suburban hot water system problems. When your Suburban hot water system is not working is can be easily diagnosed. Some of the common causes of this problem are:
- Faulty power supply
- Faulty or damaged regulator
- Faulty or damaged gas valve
Troubleshooting System Not Working Problem
Once this problem occurs, you start off by inspecting power supply dynamics. Then you rule out possible causes as you move along. Some of the remedies you can use here are:
- Ensure correct and sufficient voltage is being supplied
- Fix or replace regulator to ensure pressure is correct
- Fix or replace gas valve.
2. Water Leaks
This is another common Suburban hot water system problem – water leaks. Water leaks can be a serious issue if left unaddressed. Some of the common causes of this problem are:
- Plumbing leakages
- Pressure relief valve may be faulty or damaged
- Water pressure may not be enough
- Valves may be stuck
Troubleshooting Water Leaks Problem
There are a number of checks you must make when this water leak problem occurs. You should do this swiftly because this Suburban hot water system problem can escalate. Some of the remedies you can explore are:
- Fix or plug any leakages
- Fix or replace pressure relief valve
- Sufficiently increase water pressure
- Readjust or realign valves where necessary
3. Water Too Hot Or Not At All
Another common Suburban hot water system problem pertains to temperature dynamics. Sometimes the Suburban hot water system may not be heating the water at all. Then at times the water may be turning out too hot. This problem may be caused by:
- Thermostat could be damaged or faulty
- Water tank may be leaking
- Burner mechanism could be faulty or damaged
- Temperature and pressure valve may be damaged or faulty
Troubleshooting Water Too Hot Or Not All Problem
This is a Suburban hot water system problem requiring immediate attention. After all, the Suburban hot water system ought to properly heat water. Conduct some checks to figure out the root cause. Some of the solutions to the problem are:
- Fix or replace thermostat
- Plug leakages or replace water tank
- Fix or replace burner mechanism
- Fix or replace temperature and pressure valve
4. Unusual Or Loud Noise
It may occur that your Suburban hot water system may become unusually loud. When you hear unusual or loud noises it is an issue. Some of the probable causes of the problem are:
- Mineral and or sediment build-up
- Pressure inconsistencies
- Faulty, worn out or damaged heating element
Troubleshooting Unusual Or Loud Noise Problem
Start off by doing some checks to figure out what the root cause is. There could be times where the source of the problem is the water itself. Narrow down the possible causes and explore the following solutions:
- Clean off minerals or sediments
- Flush the water tank regularly or filter the water
- Ensure pressure is correct and sufficient
- Fix or replace heating element
5. Heating Element Keeps Switching Off
This is another common Suburban hot water system problem. You may notice that the heating element keeps switching off. This will result in the Suburban hot water system failing to sufficiently heat the water. Probable causes of this problem are:
- Faulty, damaged, or worn out heating element
- Faulty or damaged thermostat
- Faulty power supply
Troubleshooting Heating Element Keeps Switching Off Problem
This is a fairly common Suburban hot water system problem. With some basic checks you should be able to ascertain the actual cause of the problem. Some of the solutions to explore for this problem are:
- Fix or replace heating element
- Fix or replace thermostat
- Ensure power is flowing and correctly
How To Avoid Suburban Hot Water System Problems
Regularly flashing your water tank helps avoid Suburban hot water system problems. It is also important to filter your water to get rid of minerals and sediment. You must ensure there are no leakages in the tank. Ensuring correct and sufficient power is flowing helps avoid problems too. These are some of the ways through which you can avoid Suburban hot water system problems.
What Is The Capacity Of The Suburban Hot Water System?
The capacity of the Suburban hot water system is 20.3 liters. The Suburban hot water system’s maximum working pressure is 700 KPA.
How Long Does It Take For A Suburban Water Heater To Heat Up?
This will depend on the capacity. Suburban heaters range from 4 to 6, 10, 12, and 16 gallons. It takes on average 20 minutes to heat up 6 gallons. As for 16 gallons that may take as many as 30 minutes.
Conclusion
The Suburban hot water system works great, with all things considered. You just need to apply the knowledge you acquired today. This will significantly minimize or even eliminate common Suburban hot water system problems.