Let us look at log splitters. Champion Power Equipment is behind some of the log splitters you can consider. One of their models is the Champion 27 Ton Log Splitter. We shall be looking at some of the common Champion 27 Ton Log Splitter problems. Plus we will also highlight remedies to the problems.
Table of Contents
What Is The Champion 27 Ton Log Splitter?
The Champion 27 Ton Log Splitter has a 244cc single cylinder OHV engine. The Champion 27 Ton Log Splitter delivers impeccable power. It can manage logs that are up to 24 inches in length and 100 pounds in weight. One of the great features about the Champion 27 Ton Log Splitter is its ability to tip vertically for huge logs. Anyways, we have to look into the common Champion 27 Ton Log Splitter problems.
Champion 27 Ton Log Splitter Problems
There are some common Champion 27 Ton Log Splitter problems to look out for. Having knowledge of them helps you avoid them and also address them when they arise. Here are some of the common problems experienced by the Champion 27 Ton Log Splitter:
1. Engine Will Not Start
This is no doubt a common Champion 27 Ton Log Splitter problem. Upon switching it on, your Champion 27 Ton Log Splitter’s engine may not start. This problem could be caused by:
- Dirty carburetor.
- Dirty, stale, or incorrect fuel.
- Faulty or worn out spark plugs.
- Damaged recoil starter.
Troubleshooting Engine Will Not Start Problem
When your Champion 27 Ton Log Splitter’s engine fails to start you must figure the root cause. That will inform you on what you can do from the following:
- Clean or replace carburetor.
- Replace or top up fuel; ensure it is the correct type.
- Replace spark plugs.
- Replace recoil starter.
2. Log Splitter Vibrating Vigorously During Operation
When operating your Champion 27 Ton Log Splitter it should not vibrate vigorously. If it does that is an issue and it may possibly be caused by:
- Inadequate hydraulic oil.
- Air contamination in oil lines.
- Valves may be loose or leaking.
Troubleshooting Log Splitter Vibrating Vigorously During Operation Problem
This is usually a fairly easy problem to diagnose. The issue often stems from complications pertaining to the hydraulic system. Regardless you must thoroughly conduct some checks. Probable remedies to explore are:
- Top up hydraulic oil.
- Get rid of air contamination in oil lines.
- Top up all other oils e.g. engine oil where necessary.
- Ensure valves are firmly in place.
3. Wedge Is Not Cutting
This is yet another common Champion 27 Ton Log Splitter problem. Usually it occurs whilst everything else is working smoothly. This problem entails the Champion 27 Ton Log Splitter failing to split logs. This problem may be caused by:
- Blunt wedge.
- Log could be too long.
- Log may be improperly positioned.
- Faulty wedge mechanism.
Troubleshooting Wedge Is Not Cutting Problem
When you encounter this problem, start by checking the wedge mechanism. Then check to see if it may have to do with the logs themselves. When you have an idea of the source of the problem you can consider the following:
- Sharpening the wedge or replacing if need be.
- Fix or replace wedge mechanism.
- Ensure logs are not too long.
- Position the logs at the appropriate angles.
4. Low Or Erratic Driving Force In Operation
When using the Champion 27 Ton Log Splitter application of the right force is essential. There are times you may notice that your Champion 27 Ton Log Splitter’s driving force will be erratic. At times it will continuously be too low. This problem can be caused by:
- Air contamination in the oil and or fuel lines.
- Oil leakages.
- Weather may be too cold thus increasing hydraulic oil’s viscosity.
- Faulty or worn out pistons.
- Faulty or worn out pump.
- Faulty or worn out shipping plugs.
Troubleshooting Low Or Erratic Driving Force In Operation Problem
Ascertain the root cause of the problem first. Possible causes are many so do not just guess. Possible solutions you can explore are:
- Get rid of air contamination in the lines.
- Plug any oil leakages.
- Wait sufficiently for the log splitter to warm up.
- Fix or replace parts such as pistons, pump, or shipping plugs.
5. Cylinder Rod Not Moving
You may experience this problem where the cylinder rods fail to move. When your Champion 27 Ton Log Splitter goes through this challenge the possible causes are:
- Faulty or imperfectly positioned shipping plugs.
- Low or contaminated hydraulic fluid.
- Control valves may be blocked.
- Shaft coupling could be loose.
Troubleshooting Cylinder Rod Not Moving Problem
Perform the necessary checks to determine the source of the problem. It is usually straightforward to detect, diagnose and solve. When the cylinder rod of your Champion 27 Ton Log Splitter is not moving you can:
- Ensure shipping plugs are firmly in place.
- Top up or replace hydraulic fluid.
- Clear the control valves.
- Adjust the engine pump alignment.
How To Avoid Champion 27 Ton Log Splitter Problems
Use your Champion 27 Ton Log Splitter for its rightful purposes. Abusing it or cutting corners will present problems. Ensure to inspect it before and after every use. Conduct regular maintenance and servicing. This entails cleaning, oil changes, lubrication, replacing worn out components, and the like. Making all these things habits will avoid Champion 27 Ton Log Splitter problems.
How Much Hydraulic Fluid Is Needed For The Champion 27 Ton Log Splitter?
The hydraulic system of the Champion 27 Ton Log Splitter features a 6.5 gallon oil capacity. It has a 5 gallon tank and operates at 11 gpm.
What Can A 27 Ton Log Splitter Do?
It can split through wood with 27 tonnes of force. It can operate horizontally or vertically. It helps you cut through logs measuring 25 inches in diameter. It can do this in 19-second cycles. Now wonder it delivers swift operation.
Conclusion
The Champion 27 Ton Log Splitter is great piece of equipment to own. Just ensure you acquaint yourself with how it operates and it different components. This will help you use it from a position of knowledge which streamlines your user experience.